If your car requires an output converter connect this as well so your radio will work with your car. Connect the antenna cable the single wire with the big plug at the end to your new head unit as well.
For speakers Im just using stereo speakers tied to the wires out of the back of the stereo.
How to wire a car stereo. The most important thing to remember is that your car stereo probably doesnt sound as good as you might think it does. Unplug any connectors that are attached to the panels. The fact is that the sound system is one of the places that OEMs almost universally neglect in the name of higher profits and most people dont even realize what theyre missing.
WIth your car in park and cooled down pop the hood and detach the negative terminal. Connect the output converter if one is needed to make the new stereo compatible with the cars audio system. Have in mind that all wires should be connected in the end and there should no single one hanging unattended.
You can start by carefully unplugging the antennae wire which will be the thickest and will be constraining the stereo. To wire a car stereo start by disconnecting your car battery to avoid electrocuting yourself. If you find two more wires that show approximately 12V then turn the dimmer switch down and check again.
How to Install a DUAL XDVD236BT double din car stereo from start to finish for beginnersHello everyone Crimped connections are preferred method used by most. It should have holes in the side just like your old unit did. Use the panel removal tools to pop off any dashboard pieces panels or components to get to the stereo.
You can now unplug the wire harness connectors by pushing buttons or tabs which loosens them up for unplugging. Next step is to wire up the stereo harness adapter to the harness that was supplied with your new stereo. The car stereo works.
Learn how to install an aftermarket car stereo on your ownFull explanation on our blog. Most aftermarket head units will use a yellow wire for this. The yellow wire should be connecting to the batter and the red wires should ground with ignition switch and black should ground at a metal ground.
Dimmer and BlueWhite. This article explains how to identify car speaker wire colors when installing a car stereo. This was done on a 2004 GMC Yukon but as long as you can find the XM module you should be able to perform a similar operation.
The wires need to be connected color to color. After doing that you should be able to move the stereo around. Here is a detailed tutorial I made describing how to install an AUX input to your car.
Looking for a stereo or accessories for your vehicle. Plug in the antenna cable and connect the stereos wiring adapter to the the cars wire harness. Once its in snap the trim plate onto the outside.
And should ground all the wires in the car. After you have marked that wire and set it aside turn the ignition switch on turn the headlights on and turn the dimmer switch - if equipped - all the way up. I power it with a 12V power supply from Radio Shack.
Standard Aftermarket Car Stereo Head Unit Wire Colors The easiest way to wire in an aftermarket car stereo is to look at car stereo wiring diagrams for the specific vehicle and head unit but its actually possible to get the job done without any labels. Mute not required OrangeWhite. Lifewire Tim Liedtke.
For this to work your car must have XM radio capabilities. Use tape and a Sharpie to label the wires if you need to. And that isnt a judgmental statement.
My antenna is a piece of scrap 10 solid copper wire shoved into the antenna jack and held in with tape. Now all you need to do is put the new stereo into the bracket. Connect the remaining wires.
Cut a 12-18 long section of power wire attach it to one end of the fuse holder and attach the other end of the cable to the other fuse holder end. You DO NOT have to be subscribed to XM I am not. Ground the car wires with electrical tape.
Use appropriate wire stripping and crimping tools to connect terminals or solder them and cover with heat shrink tubing or electrical tape. Use the screws that came with the new car stereo. Connect the car stereo wire harness to the connector that was attached to your old radio and attach the other end to your new one.
Learn the techniques and too. Each wire serves a different purpose. My setup is an AM-FM-8 track player I got out of an Econoline motorhome in the junkyard.
After the removing of the stereo from the car battery you should disconnect the power. Diy Bri gives you in-depth instructions and tips to successfully wire a radio into any vehicle without a wiring harness adapter. They will be correctly sized.
Then match the colored wires of your radio and your car and twist the wires together.
